可訂購部件
| 型號 | 可訂購的器件編號 | 訂購代碼(12NC) | 封裝 | 從經銷商處購買 |
|---|---|---|---|---|
| NEX92730DPCD-Q100 | NEX92730DPCD-Q100Y | 935692504518 | SOT8108-1 | 訂單產品 |
Register once, drag and drop ECAD models into your CAD tool and speed up your design.
Click here for more informationNEX92730DPCD-Q100
300 mA, dual-channel antenna LDO with current sensing
The NEX92x30-Q100 devices are dual-channel, high-voltage low-dropout (LDO) regulators with current sensing, they are designed to operate with a wide range of voltage from 4 V to 40 V (45 V load dump protection). These devices provide power supply for low noise amplifiers with an active antenna through a coax cable with 300 mA per channel. It provides an adjustable output voltage from 1.5 V to 20 V for each channel.
These devices provide diagnostics through current sensing and error pins. To monitor the load current, a high-side current-sense circuitry provides a proportional analog output to the sensed load current. Accurate current sensing allows detection of open, normal, and short-circuit conditions without the need for further calibration, and current sensing multiplexing is allowed between channels to conserve analog-to-digital converter (ADC) resources. Each channel also implements adjustable current limits with an external resistor. Figure 1 shows the typical application.
The device integrates short-circuit, over-current, thermal shutdown, short-to-battery and reverse current protections. Each channel has internal inductive clamp protection on the output during inductive switch-off. It can operate at ambient temperatures ranging from -40 °C to 125 °C and junction temperatures ranging from -40 °C to 150 °C with an HTSSOP16 package.
Features and benefits
- AEC-Q100 qualified for automotive applications
- Ambient temperature (Tamb): -40 °C to 125 °C
- Junction temperature (Tj): -40 °C to 150 °C
- Input voltage range: 4 V to 40 V (45 V transient)
- Output voltage range: 1.5 V to 20 V adjustable
- Maximum output current: 300 mA per channel
- High accuracy current sensing to detect antenna/MIC open conditions at low current
- Adjustable current limit by an external resistor
- High power supply ripple rejection (PSRR): typical 80 dB at 100 Hz
- Low dropout voltage:
- 500 mV typical at 300 mA (VOUT = 8.5 V)
- Stable with a wide range of ceramic output-stability cap:
- ESR from 0.001 Ω to 5 Ω; output cap of 2.2 μF to 220 μF
- Integrated various fault protections:
- Thermal shutdown
- Short-circuit and over-current protection
- Reverse-current protection
- Output short-to-battery protection
- Output inductive load clamp
- Multiplexing current sensing between channels and devices
- Ability to identify all faults with current sensing
- 16-pin HTSSOP enhanced thermal pad package
Applications
Infotainment active-antenna power supplies
Automotive MIC power supplies
Camera power supplies
High-side power switches for small current applications
| Part number | Channel | Version | |
|---|---|---|---|
NEX92730DPCD-Q100 |
Dual |
Latch |
|
NEX92830DPCD-Q100 |
Dual |
Auto-retry |
封裝
| 型號 | 可訂購的器件編號，（訂購碼(12NC)） | 狀態 | 標示 | 封裝 | 外形圖 | 回流焊/波峰焊 | 包裝 |
|---|---|---|---|---|---|---|---|
| NEX92730DPCD‑Q100 | NEX92730DPCD‑Q100Y (935692504518) |
Active | N92730D |
HTSSOP16 (SOT8108-1) |
SOT8108-1 | 暫無信息 |
Boards
| Part number | Description | Type | Quick links | Shop link |
|---|---|---|---|---|
|
描述 This user manual describes the NEVB-NEX92830DPC. The NEX92830DPCD-Q100 is a dual-channel, high-voltage low-dropout regulator (LDO) with current sensing, designed to operate with a wide range of voltage from 4 V to 40 V (45 V load dump protection). This device provides power supply for lownoise amplifiers of active antennas through a coax cable with 300 mA per channel and an adjustable output voltage from 1.5 V to 20 V for each channel. This document contains the EVB schematic and configuration, bill of materials (BOM) and board layouts.
|
類型 Evaluation board
|
Quick links
|
Shop link
|
|
|
描述 This user manual describes the NEVB-NEX92730DPC. The NEX92730DPCD-Q100 is a dual-channel, high-voltage low-dropout regulator (LDO) with current sensing, designed to operate with a wide range of voltage from 4 V to 40 V (45 V load dump protection). This device provides power supply for low-noise amplifiers of active antennas through a coax cable with 300 mA per channel and an adjustable output voltage from 1.5 V to 20 V for each channel. This document contains the EVB schematic and configuration, bill of materials (BOM) and board layouts.
|
類型 Demo board
|
Quick links
|
Shop link
|
環境信息
| 型號 | 可訂購的器件編號 | 化學成分 | RoHS | RHF指示符 |
|---|---|---|---|---|
| NEX92730DPCD‑Q100 | NEX92730DPCD‑Q100Y | NEX92730DPCD-Q100 |
|
|
文檔 (3)
| 文件名稱 | 標題 | 類型 | 日期 |
|---|---|---|---|
| NEX92X30_Q100 | 300 mA, dual-channel antenna LDO with current sensing | Data sheet | 2025-08-01 |
| SOT8108-1 | plastic, thermal enhanced thin shrink small outline package;16 leads, 0.65mm pitch, 5.0mm × 4.4mm × 1.2mm body | Package information | 2025-07-31 |
| UM90068 | NEX92730DPCD-Q100 300 mA, dual-channel antenna LDO with current sensing evaluation board | User manual | 2025-08-06 |
Longevity
The Nexperia Longevity Program is aimed to provide our customers information from time to time about the expected time that our products can be ordered. The NLP is reviewed and updated regularly by our Executive Management Team. View our longevity program here.
模型
No documents available
訂購、定價與供貨
| 型號 | Orderable part number | Ordering code (12NC) | 狀態 | 包裝 | Packing Quantity | 在線購買 |
|---|---|---|---|---|---|---|
| NEX92730DPCD‑Q100 | NEX92730DPCD‑Q100Y | 935692504518 | Active | 暫無信息 | 2,500 |
|
樣品
作為 Nexperia 的客戶，您可以通過我們的銷售機構訂購樣品。
如果您沒有 Nexperia 的直接賬戶，我們的全球和地區分銷商網絡可為您提供 Nexperia 樣品支持。查看官方經銷商列表。
How does it work?
The interactive datasheets are based on the Nexperia MOSFET precision electrothermal models. With our interactive datasheets you can simply specify your own conditions interactively. Start by changing the values of the conditions. You can do this by using the sliders in the condition fields. By dragging the sliders you will see how the MOSFET will perform at the new conditions set.